I have a site-to-site vpn between a Pix 515E and a Sonicwall TZ190 (Orion is behind the Pix). I wasn't monitoring the TZ190 until I read this thread. Once I established that I could ping the inside interface of the TZ190, I remotely configured SNMP on the unit and the added the node to Orion. Everything's working as expected. Jay

Mar 28, 2010 · I´m trying to connect my phone to my office VPN, which uses a Cisco PIX. It works perfectly from my computer using Cisco VPN client, but I can´t make it work with my E71. I tried a lot of combinations and variations of configurations in Nokia Mobile VPN Policy Tool, but anyone works. I have a site-to-site vpn between a Pix 515E and a Sonicwall TZ190 (Orion is behind the Pix). I wasn't monitoring the TZ190 until I read this thread. Once I established that I could ping the inside interface of the TZ190, I remotely configured SNMP on the unit and the added the node to Orion. Everything's working as expected. Jay The issues would be that this isn't the cleanest of items and the other item would be what if the other side network already has vpn's setup to a network on the, say for example, 192.168.22.0/24 range. Products: Cisco PIX (IPsec) Models 506, 515, 525 and 535 Gateways, based on the PIX 6.1 Product: NetHawk VPN, an IPsec site-to-site and remote access VPN that includes policy and virtual private networks between Allied Telesis routers and Cisco PIX firewalls. It shows you how to configure a VPN between a local Allied Telesis router and a remote Cisco PIX firewall, step-by-step. On the Allied Telesis router , it uses the Site-To-Site VPN wizard for the VPN configuration.

Jan 25, 2011 · Configuring the Cisco PIX 6.x. Creating a site-to-site VPN connection on a Cisco PIX is similar but slightly different than configuring an ASA. For example, when configuring the management connection (phase 1) parameters using the same configuration used previously, use the following commands:

Mar 28, 2010 · I´m trying to connect my phone to my office VPN, which uses a Cisco PIX. It works perfectly from my computer using Cisco VPN client, but I can´t make it work with my E71. I tried a lot of combinations and variations of configurations in Nokia Mobile VPN Policy Tool, but anyone works. I have a site-to-site vpn between a Pix 515E and a Sonicwall TZ190 (Orion is behind the Pix). I wasn't monitoring the TZ190 until I read this thread. Once I established that I could ping the inside interface of the TZ190, I remotely configured SNMP on the unit and the added the node to Orion. Everything's working as expected. Jay The issues would be that this isn't the cleanest of items and the other item would be what if the other side network already has vpn's setup to a network on the, say for example, 192.168.22.0/24 range. Products: Cisco PIX (IPsec) Models 506, 515, 525 and 535 Gateways, based on the PIX 6.1 Product: NetHawk VPN, an IPsec site-to-site and remote access VPN that includes policy and

Oct 15, 2013 · The PIX is replacing an old Cisco router. The ASA is our main device which is configured for multiple VPN connections (and I have not touched this) and still has the old VPN config from that old Cisco router. On my part, I configured the PIX with the same pre-share key, and security protocols as the old router.

Hello ALL, Need suggestion!!!! My Goal- Communication between R3 loopback interface and R1 using site to site VPN. Everything is working fine but i have a doubt. Below is configuration provide. I have ACL created on PIX and on R3. ***PIX*** access-list 101 extended permit ip 10.11.11.0 255.255.255.0 My side of the Tunnel is the Netvanta 3448 and I have 16 other site-to-site VPN tunnels currently on this box. I am trying to get to connect to an older Cisco Pix on 6.3 code. I don't control or administrator the Cisco Pix side. I have an ASA 5505 at my house which i built a site-to-site tunnel to m I am trying to configure a site to site vpn on a test network. One end has pix 515E and the other has ASA 5505. I configured each side with the vpn wizard provided by each firewall. Ain't working, and don't know why. Do I have to do anything outside of the VPN wizard. Apr 13, 2012 · Here is a basic example of a site to site VPN between a Cisco ASA firewall running version 8.3 or higher, and a Cisco PIX firewall running version 6.x Configuration for the Cisco ASA side of the connection: Define network objects for your internal subnets: object network Main-Office subnet 192.168.1.0 255.255.255.0 object network Branch-Office subnet 192.168.2.0 255.255.255.0… A site-to-site VPN allows offices in multiple fixed locations to establish secure connections with each other over a public network such as the internet. Site-to-site VPN extends the company's network, making computer resources from one location available to employees at other locations. The Site-to-Site VPN Manager defines and configures site-to-site VPN topologies and policies on Cisco IOS security routers, PIX Firewalls, Catalyst VPN Service Modules, and Adaptive Security Appliance (ASA) firewall devices. Tip In ASA documentation, site-to-site VPNs are call ed LAN-to-LAN VPNs. These phrases are equivalent,